Truss Load Calculator

Truss Load Calculator
Work out the design load carried by one roof truss
Planning estimate only, using a simple uniform-load model. Real truss design must follow local building codes and be checked by a licensed structural engineer or the truss manufacturer.

Every roof truss quietly carries a surprising amount of weight. Shingles, sheathing, snow, wind driven rain and the ceiling hanging below it all add up, and the truss has to pass that load safely down to the walls. Getting the load figure right is the first step in choosing a truss that will not sag, crack the ceiling or fail in a storm, and it is also the number every truss manufacturer will ask for before quoting a design.

This Truss Load Calculator turns the standard load inputs into the figures that matter. Enter the span, spacing, truss depth and the loads your local conditions demand, and the tool returns the total load on one truss, the reaction at each bearing and an estimate of the force running through the top and bottom chords. It is built for planning, comparing designs and understanding quotes, before a licensed engineer produces the final stamped design.

What Is Truss Load

Truss load is the total force a single truss must support, built up from the loads acting on the roof area that drains onto it. Engineers describe area loads in pounds per square foot, abbreviated psf. Dead loads are the permanent weight of the structure itself, such as shingles, decking, the truss lumber and any ceiling attached to the bottom chord. Live loads come and go, with snow on the roof being the dominant one in cold climates and a standard roof live load used where snow is rare.

Because trusses repeat at regular intervals, each truss is responsible for a strip of roof as wide as its spacing. This strip is called the tributary width. A truss at twenty four inch spacing carries twice the load of an identical truss at twelve inch spacing on the same roof, which is why spacing is such a powerful lever in design. Multiply the total psf by the tributary width and you get a line load in pounds per foot along the span, the starting point for every further calculation.

How to Use the Truss Load Calculator

  1. Enter the truss span in feet, measured between the outside faces of the supporting walls.
  2. Add the truss spacing in feet. Twenty four inches on center, the common choice, is two feet.
  3. Enter the depth of the truss at its center in feet, peak to bottom chord. A rough guide for a pitched truss is a quarter of the span, but use your design figure if you have one.
  4. Type the roof dead load in psf. Ten psf suits a typical shingle roof with sheathing, and heavier finishes need more.
  5. Add the snow or roof live load in psf from your local building code or weather data.
  6. Add any ceiling dead load in psf if drywall or another ceiling hangs from the bottom chord.
  7. Press the calculate button to see the total load, reactions, bending moment and chord force.

The headline result is the total load carried by one truss, which is the number to compare against a manufacturer rating or a span table. The reaction tells you the downward force each wall and bearing point must receive, which matters for wall framing and any beams or posts below. The chord force estimate shows the tension and compression the main timbers must resist.

How the Calculation Works

The calculator first adds the three area loads together to get a total design load in psf. It multiplies that figure by the tributary width, which is simply the spacing, to get a uniform line load in pounds per linear foot along the truss. Multiplying the line load by the span gives the total load on the truss, and because the load is uniform and the truss rests on two supports, each bearing carries half, which is the reaction.

The bending moment uses the classic formula for a uniformly loaded beam, load multiplied by span squared, divided by eight. A truss resists that moment mainly as a couple, meaning a push in one chord and a pull in the other, separated by the depth of the truss. Dividing the moment by the depth therefore estimates the maximum chord force. Real trusses distribute forces through webs and joints in a more detailed pattern, and heels, pitches and point loads change the details, but this simple model gets the scale of the forces right and is ideal for comparing options.

The Inputs Explained

  • Truss span. The clear distance the truss must bridge. Load grows quickly with span because both the length and the bending moment increase.
  • Truss spacing. The on center distance between trusses. Wider spacing puts more roof onto each truss.
  • Truss depth. The vertical distance between chords at mid span. Deeper trusses resist bending with lower chord forces.
  • Roof dead load. The permanent weight of roofing, decking, underlayment and the truss itself, in psf of roof area.
  • Snow or live load. The temporary load your code requires, usually ground snow converted to roof snow, or a standard roof live load in warm regions.
  • Ceiling dead load. Weight hanging from the bottom chord, such as drywall at roughly two to three psf plus insulation and fixtures.

Loads in this tool are entered as service level figures for planning. Formal design applies load combinations and safety factors from the governing code, and local amendments can change the required snow, wind and seismic values significantly. Always confirm the psf figures with your building department or the design professional on the project.

A Worked Example

Consider a garage roof with trusses spanning forty feet at two foot spacing, with a center depth of five feet. The shingle roof has a dead load of ten psf, the local snow load is thirty psf, and a drywall ceiling adds five psf, for a total design load of forty five psf. The tributary strip is two feet wide, so the line load on each truss is ninety pounds per foot.

Multiplying along the span, one truss carries three thousand six hundred pounds in total, delivering one thousand eight hundred pounds to each wall. The maximum bending moment works out to eighteen thousand pound feet, and dividing by the five foot depth estimates a maximum chord force of three thousand six hundred pounds. Numbers like these explain why spacing matters so much. Widening the spacing to four feet would double every one of these figures on each truss.

Dead Load, Live Load and Snow Load

Dead load is the load that never leaves. Roofing materials dominate it on the top chord, and typical values run from about seven psf for light metal roofing to fifteen psf or more for tile. The bottom chord carries its own dead load when a ceiling is attached. Because dead load acts forever, it also drives long term creep and sag, which is why ceiling cracking sometimes appears under trusses that were strong enough on day one.

Snow is usually the largest live load and the least forgiving of guesswork. Building codes publish ground snow values by location, then convert them to roof snow using factors for slope, exposure and importance. Drifting against higher walls and valleys can multiply the uniform figure locally. Where snow is not a factor, codes substitute a minimum roof live load intended to cover workers and materials during construction and repairs. Use the figure your jurisdiction demands, not the mildest winter you can remember.

Why Spacing and Depth Change Everything

Spacing controls how much roof each truss must carry, so it scales the total load in direct proportion. Halving the spacing halves the load per truss but doubles the number of trusses, a trade that often favors labor and redundancy over material. Depth works differently. It does not change the load at all, but it changes how hard the chords must work to resist it, because a deeper truss has more leverage. Doubling the depth roughly halves the chord force for the same moment.

These two levers explain most real world design choices. Long spans get deeper trusses, tighter spacing, or both. When a quote comes back much cheaper than expected, it is worth checking which lever was quietly moved, because the load itself, set by the roof and the climate, never changes.

Limitations of This Estimate

The model treats the load as perfectly uniform and the truss as a simple beam, which is an approximation. Point loads from rooftop units, hoists, solar arrays or a change of roof level concentrate force in ways this tool does not capture. Wind uplift, which can reverse forces and pull up on the roof, is a separate calculation, as are seismic effects and the detailed design of webs, plates and connections.

Treat the output as a planning estimate with the right order of magnitude, suitable for budgeting, comparing layouts and sanity checking a supplier span table. Final truss design belongs to the manufacturer engineering software and a licensed professional who can stamp the drawings for your jurisdiction.

Frequently Asked Questions

What is truss load?

Truss load is the total force one truss must support from the roof area that drains onto it. It combines dead loads such as roofing and ceiling weight with live loads such as snow, converts them through the truss spacing into a line load, and accumulates that along the span. It is the starting figure for sizing chords, webs and bearings.

What does tributary width mean in truss design?

Tributary width is the strip of roof whose load lands on one truss. For evenly spaced trusses it equals the spacing, because each truss picks up half the distance to its neighbor on both sides. End trusses at gables carry a narrower strip. Multiplying area load in psf by tributary width gives the line load the truss actually feels.

How is the load on one truss calculated?

Add the dead, live or snow, and ceiling loads to get a total in psf. Multiply by the spacing in feet to get pounds per linear foot, then multiply by the span to get the total load on the truss. This calculator performs those steps and also derives the bearing reactions, the maximum bending moment and an estimated chord force.

What is a typical roof dead load?

A common planning figure is ten psf for an asphalt shingle roof with plywood or OSB decking, felt and the truss weight itself. Light metal roofing can be lower, while concrete tile can push the total well past fifteen psf. Ceiling drywall hung from the bottom chord adds roughly two to five psf more, depending on thickness and insulation.

How much does snow load change the design?

Snow is often the single largest load on the truss. Moving from a twenty psf snow zone to a fifty psf snow zone can nearly double the total load and the chord forces, which is why the same truss design cannot simply be copied between regions. Local code values, plus drift provisions near roof steps and valleys, should always set the figure you enter.

What truss spacing is most common?

Twenty four inches on center is the standard for most residential and light commercial roofs, balancing material cost against sheathing stiffness. Sixteen inch spacing appears on heavy load or long span work, and wider engineered spacings show up in post frame buildings. Whatever spacing you choose must match the figure used in the load calculation, since the two move together.

What is the difference between total load and design load?

Total load in psf is the sum of the area loads acting on the roof, and it is an input to design. The total load on one truss, in pounds, is the accumulated force that truss must carry after spacing and span are applied. Formal design then applies code load combinations and factors to those service loads to size each member with a margin of safety.

How is chord force estimated in this calculator?

The tool divides the maximum bending moment by the truss depth at mid span. A truss resists bending mainly as a pair of equal and opposite forces in its top and bottom chords, so moment divided by the lever arm between them gives a good estimate of peak chord force. Web members and joints then need their own detailed checks in a full design.

What is the difference between psf and plf?

Psf, pounds per square foot, describes load spread over an area, like snow lying on a roof. Plf, pounds per linear foot, describes load along a line, like the force running along a truss. Spacing converts one to the other. Multiply psf by the tributary width in feet and the result is the plf the truss must carry.

Can I use this calculator for floor trusses?

The arithmetic works the same way, but floor loads are very different in size and character. Floors carry much higher live loads, often forty psf or more for living areas, plus strict deflection and vibration limits that rarely trouble a roof. You can run the numbers for a floor truss to get the total load, but member sizing should come from floor specific span tables or an engineer.

How does span length affect truss load?

Total load grows in direct proportion to span, since a longer truss collects load from more roof. Bending moment grows with the square of the span, which is the tougher effect. Doubling the span doubles the total load but quadruples the moment and roughly the chord force unless the truss also gets deeper, which is why long spans change design so dramatically.

What is a bearing reaction?

The reaction is the downward force the truss delivers to each support, usually the top plate of a wall. Under a uniform load each end carries half the total. Reactions size the bearing area, the wall framing below, and any beam, header or post that picks the truss up, so crushing or under framing at that point is a common and avoidable problem.

Does this calculator replace a structural engineer?

No. It provides planning level estimates using a simplified uniform load model. It does not run code load combinations, check individual members and connector plates, or account for wind uplift, point loads and local amendments. Final truss designs should come from the manufacturer engineering and, where required, a licensed structural engineer who stamps the drawings.

What load combinations do building codes use?

Codes such as the IBC and ASCE 7 combine loads with factors, checking cases like dead plus snow, dead plus live, and dead plus wind, each weighted to reflect how likely the loads are to peak together. Designers check both strength level and allowable stress combinations. The psf figures you enter here are service loads, before those combinations are applied by the design professional.

How can I reduce the load carried by each truss?

The load itself is set by the roof build up and climate, but the load per truss can be cut by tightening the spacing, which spreads the same roof across more trusses. Choosing lighter roofing lowers dead load a little. Adding depth does not reduce load but reduces chord force for the same load. Any change must stay consistent across the whole roof system, including sheathing spans.